International Peer-Reviewed Journal•Open Access•ISSN 2456-8880
[email protected]•+91-7433024337

Home / Current Issue / Paper 1725324

1725324 Vol 10 · Issue 5 Download Paper

Comparative Analysis of Transmission and Attenuation Coefficients of Silane-Treated Sodium Lime Glass/Polycaprolactone Composites Fabricated by the Melt Blend Technique

Bashir Yahaya Bilyaminu Usman Ahmed Jimoh Ibrahim Magaji Kotorkoshi

Subject area: Science,Engineering and Technology  ·  Area of research: Polymer Composite Materials

Abstract

The growing use of electronic and wireless devices has increased the need for lightweight, low-cost materials that attenuate microwave radiation. Conventional absorbers based on ferrite and carbon are expensive, environmentally hazardous and non-recyclable. This study investigates waste sodium lime glass (NLG) cullet as a microwave-attenuating filler in a biodegradable polycaprolactone (PCL) matrix, with particular attention to the effect of silane surface treatment. The glass was crushed, ball-milled to a micrometre-sized powder, and functionalised with 3-aminopropyltriethoxysilane (APTES) to improve its compatibility with the hydrophobic polymer. The treated particles were incorporated into molten PCL by melt blending at filler loadings of 12.5, 22.5, 37.5, 50.0 and 62.5 wt%, and the blends were cast in a stainless-steel mould. The complex permittivity of the composites was measured over the X-band (8–12 GHz) using an open-ended coaxial probe connected to a vector network analyser. The transmission coefficient (S21) was measured in a rectangular waveguide, and the attenuation was calculated from it. The finite element method in COMSOL Multiphysics was used to determine the transmission and attenuation coefficients numerically. The results show that the transmission coefficient decreases steadily as filler content increases, consistent with impedance mismatch theory and with effective dispersion of the filler in the matrix. Attenuation therefore rises with filler loading, from its lowest value at 12.5 wt% NLG to its highest at 62.5 wt% NLG. The composites achieved shielding effectiveness between 3.4 and 6.5 dB. These findings show that recycled glass and PCL can be combined into a cost-effective, environmentally friendly microwave shielding material. Such materials can be tailored for use in the electronics, telecommunications and medical industries.

Keywords

Electromagnetic shielding, finite element method, microwave attenuation, polycaprolactone, sodium lime glass

References

[1] Ul Haq I, Ghaffar A, Ahmad R. Enhancement and dissipation of electromagnetic energy in a four-level tripod atomic system. Physica Scripta. 2025;100(8):085119.

[2] Jia N, Xue L, Cui H. Mitigating EMI noise in propagation paths: Review of parasitic and coupling effects in power electronic packages, filters, and systems. IEEE Open J Power Electron. 2024;5:352–368.

[3] Aiqiong W, Li J, Chen M, Zhao X. A review of graphene-based broad bandwidth microwave absorbing textile-based composites in the low-frequency range. J Ind Textiles. 2022;52:15280837221133113.

[4] Nayak L, Chaki TK, Khastgir D. Electrical percolation behavior and electromagnetic shielding effectiveness of polyimide nanocomposites filled with carbon nanofibers. J Appl Polym Sci. 2014;131(24). https://doi.org/10.1002/app.40914

[5] Patil VP, et al. Effect of annealing on structural, morphological, electrical and optical studies of nickel oxide thin films. J Surf Eng Mater Adv Technol. 2011;1:35. https://doi.org/10.4236/jsemat.2011.12006

[6] Thomas SW, Khan RR, Puttananjegowda K, Serrano-Garcia W. Conductive polymers and metal oxide polymeric composites for nanostructures and nanodevices. In: Advances in Nanostructured Materials and Nanopatterning Technologies. Elsevier; 2020. p. 243–271.

[7] Shao Y, Liu J, Wang Y, Lin Y. Novel catalyst support materials for PEM fuel cells: Current status and future prospects. J Mater Chem. 2009;19(1):46–59.

[8] Li GJ, Huang XX, Shi Y, Guo JK. Preparation and characteristics of nanocrystalline NiO by organic solvent method. Mater Lett. 2001;51(4):325–330. https://doi.org/10.1016/S0167-577X(01)00312-3

[9] Santos HF, Carmo FL, Paes JE, Rosado AS, Peixoto RS. Bioremediation of mangroves impacted by petroleum. Water Air Soil Pollut. 2011;216(1):329–350.

[10] Donald IW. Waste immobilization in glass and ceramic based hosts: Radioactive, toxic and hazardous wastes. John Wiley & Sons; 2010.

[11] Dziadek M, et al. Polyphenolic compounds affect the long-term degradation behaviour of polymer and composite materials based on PCL, PLGA, and bioactive glass. Sustain Mater Technol. 2023;35:e00568.

[12] Tao H, et al. Progress in preparation, processing, and application of high dielectric polypropylene matrix composite materials. Polym Compos. 2024;45(6):4819–4838.

[13] Mao H, Chen X, Wang F, Zhang W. Effects of alkaline earth oxides on the densification and microwave properties of low-temperature fired BaO–Al2O3–SiO2 glass–ceramic/Al2O3 composites. J Mater Sci. 2019;54(19):12371–12380.

[14] Assis SRH, Lira BB, Rêgo SABC. Desenvolvimento e caracterização de peças cerâmicas utilizando vidro reciclado como alternativa de reaproveitamento de resíduos. In: Proceedings of the 21st CBECIMAT – Congresso Brasileiro de Engenharia e Ciência dos Materiais; 2014; Cuiabá, Brazil. (in Portuguese)

[15] Matos M, Coutinho JS. Durability of mortar using waste glass powder as cement replacement. Constr Build Mater. 2012;36:205–215.

[16] Aziz T, et al. Recent progress in silane coupling agent with its emerging applications. J Polym Environ. 2021;29(11):3427–3443.

[17] Jimoh A, Yakubu A, Bilyaminu U, Usman S, Nagogo S. Power loss, attenuation and electric field intensity determination of PCL/rice husk using numerical technique for microwave application. Brilliant Eng. 2024;4:4967. https://doi.org/10.36937/ben.2024.4967

[18] Yakubu A, Jimoh A, Abbas M, Usman B, Adetoro AW. Determination of transmission coefficient and electric field distribution of rice husk/PCL composites using finite element method for microwave devices. J Nature Sci Technol. 2022;2:6647. https://doi.org/10.36937/janset.2022.6647

[19] Liu J, Zhang L, Wu H. Electromagnetic wave-absorbing performance of carbons, carbides, oxides, ferrites and sulfides: Review and perspective. J Phys D Appl Phys. 2021;54(20):203001.

[20] Awadeen M, Amin M, Bakr RH, Tahwia AM. Mechanical properties, attenuation coefficient, and microstructure of ultra high-performance heavyweight concrete for radiation shielding applications. J Build Eng. 2024;82:108395.

[21] Hagino K. Simple schematic model for transmission coefficients in the isolated resonance region. Phys Rev C. 2025;112(3):034611.

[22] Li E, et al. Current-diffusion model for metasurface structure discoveries with spatial-frequency dynamics. Nature Mach Intell. 2026;8(1):59–69.

[23] Wang L, Yang J, Cheng W, Zou J, Zhao D. Progress on polymer composites with low dielectric constant and low dielectric loss for high-frequency signal transmission. Front Mater. 2021;8:774843.

[24] Vovchenko L, Matzui L, Zagorodnii V, Yakovenko O. The effect of filler distribution on electromagnetic properties of nanocarbon/magnetic particles/polymer composites. J Appl Phys. 2024;136(18).

[25] Alrashdan MH. Achieving desired characteristic impedances in customized coplanar waveguide transmission line design. MethodsX. 2024;13:103074.

[26] Siraj S, Al-Marzouqi AH, Iqbal MZ, Ahmed W. Impact of micro silica filler particle size on mechanical properties of polymeric based composite material. Polymers. 2022;14(22):4830.

How to cite this paper

Bashir Yahaya, Bilyaminu Usman, Ahmed Jimoh, Ibrahim Magaji Kotorkoshi "Comparative Analysis of Transmission and Attenuation Coefficients of Silane-Treated Sodium Lime Glass/Polycaprolactone Composites Fabricated by the Melt Blend Technique" Iconic Research And Engineering Journals Volume 10 Issue 5 2026 Page 3537-3545
Bashir Yahaya, Bilyaminu Usman, Ahmed Jimoh, Ibrahim Magaji Kotorkoshi "Comparative Analysis of Transmission and Attenuation Coefficients of Silane-Treated Sodium Lime Glass/Polycaprolactone Composites Fabricated by the Melt Blend Technique" Iconic Research And Engineering Journals, vol. 10, no. 5, Nov. 2026
Bashir Yahaya, Bilyaminu Usman, Ahmed Jimoh, Ibrahim Magaji Kotorkoshi (2026). Comparative Analysis of Transmission and Attenuation Coefficients of Silane-Treated Sodium Lime Glass/Polycaprolactone Composites Fabricated by the Melt Blend Technique. Iconic Research And Engineering Journals, 10(5).
Bashir Yahaya, Bilyaminu Usman, Ahmed Jimoh, Ibrahim Magaji Kotorkoshi "Comparative Analysis of Transmission and Attenuation Coefficients of Silane-Treated Sodium Lime Glass/Polycaprolactone Composites Fabricated by the Melt Blend Technique" Iconic Research And Engineering Journals, vol. 10, no. 5, Nov. 2026.
@article{1725324,
      author = {Bashir Yahaya, Bilyaminu Usman, Ahmed Jimoh, Ibrahim Magaji Kotorkoshi},
      title = {Comparative Analysis of Transmission and Attenuation Coefficients of Silane-Treated Sodium Lime Glass/Polycaprolactone Composites Fabricated by the Melt Blend Technique},
      journal = {Iconic Research And Engineering Journals},
      year = {2026},
      volume = {10},
      number = {5},
      pages = {3537-3545},
      issn = {2456-8880},
      url = {https://www.irejournals.com/formatedpaper/1725324.pdf},
      abstract = {The growing use of electronic and wireless devices has increased the need for lightweight, low-cost materials that attenuate microwave radiation. Conventional absorbers based on ferrite and carbon are expensive, environmentally hazardous and non-recyclable. This study investigates waste sodium lime glass (NLG) cullet as a microwave-attenuating filler in a biodegradable polycaprolactone (PCL) matrix, with particular attention to the effect of silane surface treatment. The glass was crushed, ball-milled to a micrometre-sized powder, and functionalised with 3-aminopropyltriethoxysilane (APTES) to improve its compatibility with the hydrophobic polymer. The treated particles were incorporated into molten PCL by melt blending at filler loadings of 12.5, 22.5, 37.5, 50.0 and 62.5 wt%, and the blends were cast in a stainless-steel mould. The complex permittivity of the composites was measured over the X-band (8–12 GHz) using an open-ended coaxial probe connected to a vector network analyser. The transmission coefficient (S21) was measured in a rectangular waveguide, and the attenuation was calculated from it. The finite element method in COMSOL Multiphysics was used to determine the transmission and attenuation coefficients numerically. The results show that the transmission coefficient decreases steadily as filler content increases, consistent with impedance mismatch theory and with effective dispersion of the filler in the matrix. Attenuation therefore rises with filler loading, from its lowest value at 12.5 wt% NLG to its highest at 62.5 wt% NLG. The composites achieved shielding effectiveness between 3.4 and 6.5 dB. These findings show that recycled glass and PCL can be combined into a cost-effective, environmentally friendly microwave shielding material. Such materials can be tailored for use in the electronics, telecommunications and medical industries.},
      keywords = {Electromagnetic shielding, finite element method, microwave attenuation, polycaprolactone, sodium lime glass},
      month = {November},
  }