International Peer-Reviewed Journal•Open Access•ISSN 2456-8880
[email protected]•+91-7433024337

Home / Current Issue / Paper 1725348

1725348 Vol 10 · Issue 5 Download Paper

Development of Cement Mortar Incorporating a Natural Biopolymer for Potential Use in Extrusion-Based 3D Printing

John Oluwole Labiran Ajibode Daniel Olayimika

Subject area: Science,Engineering and Technology  ·  Area of research: Civil Engineering

Abstract

This study developed and evaluated cement mortar with a natural biopolymer Ceratonia siliqua seed gum, which could be used in extrusion-based 3D printing. A total of 9 formulations included a plain control, chemical-admixture control and seven dosages of biopolymer, 0.1 to 0.8% by cement mass. Cement:sand ratio and nominal added-water-cement were about 1:1.25 and 0.32, respectively. Flow-table observations and manual mass extrusion through a 30 mm outlet were made; the chemically modified compression batches contained an accelerator. The rate of mass extrusion was 2.92 g/s for plain mortar and 6.54 g/s for the admixture control and reached its maximum with 0.3% biopolymer (7.08 g/s). The corresponding three-day strengths were 20.53, 28.83 and 30.25 MPa. The extrusion rate and strength of the 0.3% formulation were 8.28% and 4.93% higher than the admixture control, respectively. Increased dosages raised recorded flow-table D2 values but decreased extrusion rate and strength. The dosage of 0.3% is thus a candidate to be tested further and not a proven optimum. The limitations of interpretation include manual actuation, missing replicate data, and missing specimen documentation, whereas the pumpability, multilayer buildability and interlayer performance are not verified.

Keywords

cement mortar, Ceratonia siliqua, early compressive strength, extrusion-based 3D printing, manual extrusion, natural biopolymer

References

[1] Buswell RA, Leal de Silva WR, Jones SZ, Dirrenberger J. 3D printing using concrete extrusion: a roadmap for research. Cem Concr Res. 2018;112:37–49. https://doi.org/10.1016/j.cemconres.2018.05.006

[2] Roussel N. Rheological requirements for printable concretes. Cem Concr Res. 2018;112:76–85. https://doi.org/10.1016/j.cemconres.2018.04.005

[3] Le TT, Austin SA, Lim S, Buswell RA, Gibb AGF, Thorpe T. Mix design and fresh properties for high-performance printing concrete. Mater Struct. 2012;45(8):1221–1232. https://doi.org/10.1617/s11527-012-9828-z

[4] Kazemian A, Yuan X, Cochran E, Khoshnevis B. Cementitious materials for construction-scale 3D printing: laboratory testing of fresh printing mixture. Constr Build Mater. 2017;145:639–647. https://doi.org/10.1016/j.conbuildmat.2017.04.015

[5] Barak S, Mudgil D. Locust bean gum: processing, properties and food applications—A review. Int J Biol Macromol. 2014;66:74–80. https://doi.org/10.1016/j.ijbiomac.2014.02.017

[6] González-Aviña JV, Hosseinpoor M, Yahia A, Durán-Herrera A. New biopolymers as viscosity-modifying admixtures to improve the rheological properties of cement-based materials. Cem Concr Compos. 2024;146:105409. https://doi.org/10.1016/j.cemconcomp.2023.105409

[7] González-Aviña JV, Hosseinpoor M, Yahia A, Durán-Herrera A. Synergistic effects of superplasticizers and biopolymer-based viscosity-modifying admixtures on the rheology of cement-based systems. Cem Concr Compos. 2024;154:105807. https://doi.org/10.1016/j.cemconcomp.2024.105807

[8] Reiter L, Wangler T, Anton A, Flatt RJ. Setting on demand for digital concrete—Principles, measurements, chemistry, validation. Cem Concr Res. 2020;132:106047. https://doi.org/10.1016/j.cemconres.2020.106047

[9] Perrot A, Rangeard D, Nerella VN, Mechtcherine V. Extrusion of cement-based materials—An overview. RILEM Tech Lett. 2018;3:91–97. https://doi.org/10.21809/rilemtechlett.2018.75

[10] Perrot A, Rangeard D, Pierre A. Structural built-up of cement-based materials used for 3D-printing extrusion techniques. Mater Struct. 2016;49(4):1213–1220. https://doi.org/10.1617/s11527-015-0571-0

[11] Suiker ASJ, Wolfs RJM, Lucas SM, Salet TAM. Elastic buckling and plastic collapse during 3D concrete printing. Cem Concr Res. 2020;135:106016. https://doi.org/10.1016/j.cemconres.2020.106016

[12] Le TT, Austin SA, Lim S, Buswell RA, Law R, Gibb AGF, Thorpe T. Hardened properties of high-performance printing concrete. Cem Concr Res. 2012;42(3):558–566. https://doi.org/10.1016/j.cemconres.2011.12.003

[13] Nerella VN, Hempel S, Mechtcherine V. Effects of layer-interface properties on mechanical performance of concrete elements produced by extrusion-based 3D-printing. Constr Build Mater. 2019;205:586–601. https://doi.org/10.1016/j.conbuildmat.2019.01.235

How to cite this paper

John Oluwole Labiran, Ajibode Daniel Olayimika "Development of Cement Mortar Incorporating a Natural Biopolymer for Potential Use in Extrusion-Based 3D Printing" Iconic Research And Engineering Journals Volume 10 Issue 5 2026 Page 3899-3910
John Oluwole Labiran, Ajibode Daniel Olayimika "Development of Cement Mortar Incorporating a Natural Biopolymer for Potential Use in Extrusion-Based 3D Printing" Iconic Research And Engineering Journals, vol. 10, no. 5, Nov. 2026
John Oluwole Labiran, Ajibode Daniel Olayimika (2026). Development of Cement Mortar Incorporating a Natural Biopolymer for Potential Use in Extrusion-Based 3D Printing. Iconic Research And Engineering Journals, 10(5).
John Oluwole Labiran, Ajibode Daniel Olayimika "Development of Cement Mortar Incorporating a Natural Biopolymer for Potential Use in Extrusion-Based 3D Printing" Iconic Research And Engineering Journals, vol. 10, no. 5, Nov. 2026.
@article{1725348,
      author = {John Oluwole Labiran, Ajibode Daniel Olayimika},
      title = {Development of Cement Mortar Incorporating a Natural Biopolymer for Potential Use in Extrusion-Based 3D Printing},
      journal = {Iconic Research And Engineering Journals},
      year = {2026},
      volume = {10},
      number = {5},
      pages = {3899-3910},
      issn = {2456-8880},
      url = {https://www.irejournals.com/formatedpaper/1725348.pdf},
      abstract = {This study developed and evaluated cement mortar with a natural biopolymer Ceratonia siliqua seed gum, which could be used in extrusion-based 3D printing. A total of 9 formulations included a plain control, chemical-admixture control and seven dosages of biopolymer, 0.1 to 0.8% by cement mass. Cement:sand ratio and nominal added-water-cement were about 1:1.25 and 0.32, respectively. Flow-table observations and manual mass extrusion through a 30 mm outlet were made; the chemically modified compression batches contained an accelerator. The rate of mass extrusion was 2.92 g/s for plain mortar and 6.54 g/s for the admixture control and reached its maximum with 0.3% biopolymer (7.08 g/s). The corresponding three-day strengths were 20.53, 28.83 and 30.25 MPa. The extrusion rate and strength of the 0.3% formulation were 8.28% and 4.93% higher than the admixture control, respectively. Increased dosages raised recorded flow-table D2 values but decreased extrusion rate and strength. The dosage of 0.3% is thus a candidate to be tested further and not a proven optimum. The limitations of interpretation include manual actuation, missing replicate data, and missing specimen documentation, whereas the pumpability, multilayer buildability and interlayer performance are not verified.},
      keywords = {cement mortar, Ceratonia siliqua, early compressive strength, extrusion-based 3D printing, manual extrusion, natural biopolymer},
      month = {November},
  }